0.2 μm pore size 80 % porosity shipped in ambient Description General description Filter Code: JGWP Filter Type: Screen filter Our Fluoropore® membrane is a hydrophobic, polytetrafluoroethylene (PTFE) polymer membrane bonded to a high density polyethylene support to improve the handling characteristics of the filter for normal applications.
Our LifeASSURE™ PFS Series Filter Cartridges are constructed to achieve high air flow at a given pressure drop. The PTFE membrane is pleated with polypropylene nonwoven flow-enhancing layers during construction to achieve optimal flow rate performance at low differential pressures.
Filter Media: PTFE on a polypropylene support Housing: Polypropylene Filter Diameter 50 mm Effective Filtration Area 19.6 cm2 Typical Air Flow Rates 0.2 μm: 8 Lpm at 0.2 bar (20 kPa, 3 psi) 0.45 μm: 12 Lpm at 0.2 bar (20 kPa, 3 psi) 1 μm: 15 Lpm at 0.2 bar (20 kPa, 3 psi) Maximum Operating Temperature 130 °C (266 °F) at 1.0 bar (100 kPa
No significant change observed in flow rate or bubble R PP PTFE (polytetra-fluoro-PVDF ... Solvent Compatibility Chart for Filters Vials Author: Restek Corporation
Mexico 0.2 um PTFE syringe filter with high quality Polypropylene, nylon, and PTFE membranes are ideal for sample preparation and small volume chemical filtration.Syringe filters are attached to the end of a syringe to remove particles from a sample prior to analysis.
Filter Media: PTFE on a polypropylene support Housing: Polypropylene Filter Diameter 50 mm Effective Filtration Area 19.6 cm2 Typical Air Flow Rates 0.2 μm: 8 Lpm at 0.2 bar (20 kPa, 3 psi) 0.45 μm: 12 Lpm at 0.2 bar (20 kPa, 3 psi) 1 μm: 15 Lpm at 0.2 bar (20 kPa, 3 psi) Maximum Operating Temperature 130 °C (266 °F) at 1.0 bar (100 kPa
Choosing a filter does not have to be complicated – Corning has simplified the process. Just follow these four easy steps: Step 1: Match your application with the appropriate pore size. Step 2: Select the membrane and housing material for your application. Step 3: Select the correct membrane area to optimize flow rate and throughput.
• Color-coded caps allow easy identification of 0.2 µm or 0.45 µm membranes in PVDF, PTFE, PES, or nylon. • Pre-slit PTFE/silicone caps help eliminate broken autosampler needles and cored septa. • Low dead volume units feature rugged polypropylene vial and insert with 450 μL loading capacity.
Sample filtration using syringe filters containing 0.45 μm (HPLC) or 0.2 μm (UHPLC) pore size membranes will also extend the life of chromatography columns by preventing particulate from blocking the flow path between the column packing. PTFE membrane is highly chemically compatible for the filtration of harsh solvents that can destroy other
These PTFE filter cartridges can withstand up to 1 bar (14.5 psi) differential pressure (forward direction) under steam sterilization conditions (125°C). This is combined with high flow rates and excellent dewetting characteristics resulting in very economical filtration through the use of smaller installations and reduced energy costs.
Color-coded caps allow easy identification of 0.2 μm or 0.45 μm membranes in PVDF, PTFE, PES, or nylon. Preslit PTFE/silicone caps help eliminate broken autosampler needles and cored septa. Rugged polypropylene vial houses insert with 450 μL loading capacity and low dead volume (120 μL).
Fluoropore Membrane Filter 0.22 µm pore size, hydrophobic PTFE, 47 mm membrane; Synonyms: Hydrophobic PTFE membrane filter discs,Hydrophobic Polytetrafluoroethylene membrane filter discs; find Millipore-FGLP04700 MSDS, related peer-reviewed papers, technical documents, similar products & more at Sigma-Aldrich
Choosing a filter does not have to be complicated – Corning has simplified the process. Just follow these four easy steps: Step 1: Match your application with the appropriate pore size. Step 2: Select the membrane and housing material for your application. Step 3: Select the correct membrane area to optimize flow rate and throughput.
high flow rate 0.22 um PTFE syringe filter Restek Thomson SINGLE StEP Standard Filter Vials Easy-to-use vials offer fast sample filtration and require only a squeeze of your fingers. Minimize sample loss by eliminating multiple transfers. Color-coded caps allow easy identification of 0.2 μm or 0.45 μm membranes in PVDF, PTFE, PES, or nylon.